Dateien hochladen nach „transform_modules/whoosh“

transform_modules/whoosh/whoosh.ino

@@ -0,0 +1,167 @@
+/*
+WHOOSH
+// board info: LilyGO TTGO T8 ESP32-S2 - with SD Card Slot
+// board select: ESP32S2 DEV Module
+
+current USB port: 142300
+
+
+
+To DO:
+define pins for all the inputs!
+redefine range for parameters?
+
+*/
+
+
+
+#define sensor1 1  // PCB: 41 // potentiometer: font RV1
+#define sensor2 2  // PCB: 46 // potentiometer: paraA RV2
+#define sensor3 3  // PCB: 45 // potentiometer: paraB RV3
+#define sensor4 4  // PCB: 42 // potentiometer: paraC RV4
+#define sensor5 5  // PCB: 36 // potentiometer: paraD RV5
+#define sensor6 6  // PCB: 37 // potentiometer: paraE RV6
+#define sensor7 7  // PCB: 38 // potentiometer: paraF RV7
+#define sensor8 8  // PCB: 40 // potentiometer: paraG RV8
+#define sensor9 16  // PCB: 39 // slide potentiometer: paraLine RV9
+#define sensorLED 0 // LED
+
+String input;
+String newData;
+String output;
+String moduleID = "#WH";
+
+
+// the setup routine runs once when you press reset:
+void setup() {
+  // initialize serial and serial1 communication at 115200 and 9600 bits per second:
+  Serial.begin(115200);  //goes to serial monitor, just for debugging purposes
+  Serial1.begin(9600); // goes to the next module via patch cable (use transmit pin TX on IO17 and also connect to GND)
+
+  Serial1.setTimeout(100); // there is a small bug, so there needs to be a checksum?
+     
+  // set mode for digital input to not give floating values, but either 0 or 1:
+  pinMode(sensorLED, OUTPUT); // set LED pin to output
+  //LED initial state
+  digitalWrite(sensorLED, LOW);
+
+}
+
+
+
+
+// the loop routine runs over and over again forever:
+void loop() {
+
+
+  // sensor 1: font
+  // read analog input
+  int sensorValue1 = analogRead(sensor1);
+  // redefine range for font:
+  int value1 = map(sensorValue1, 0, 8191, 8191, 0);
+  // use value1 to define font: not get int but string with fontname:
+  String font = "";
+  if(value1 >= 0 && value1 < 1) {font = "T-1";} // if value1 is bigger than or equal to 1 and value1 is smaller than or equal to 10: Times-Roman
+  else if(value1 >= 1 && value1 <= 2) {font = "T-2";} // else if value1 is bigger than or equal to 11 and value1 is smaller than or equal to 20: Times-Bold
+  else if(value1 >= 50 && value1 <= 920) {font = "T-3";}
+  else if(value1 >= 921 && value1 <= 1830) {font = "T-4";}
+  else if(value1 >= 1831 && value1 <= 3199) {font = "H-1";}
+  else if(value1 >= 3200 && value1 <= 4399) {font = "H-2";}
+  else if(value1 >= 4400 && value1 <= 5600) {font = "H-3";}
+  else if(value1 >= 5601 && value1 <= 6350) {font = "H-4";}
+  else if(value1 >= 6351 && value1 <= 7250) {font = "C-1";}
+  else if(value1 >= 7251 && value1 <= 7870) {font = "C-2";}
+  else if(value1 >= 7871 && value1 <= 8189) {font = "C-3";}
+  else if(value1 >= 8190 && value1 <= 8191) {font = "C-4";}
+
+
+
+  // sensor 2: paraA
+  // read analog input
+  int sensorValue2 = analogRead(sensor2);
+  // redefine range:
+  int paraA = map(sensorValue2, 0, 8191, 5, 2);
+
+
+  // sensor 3: paraB
+  // read analog input
+  int sensorValue3 = analogRead(sensor3);
+  // redefine range:
+  int paraB = map(sensorValue3, 0, 8191, 5, 2);
+
+
+  // sensor 4: paraC
+  // read analog input
+  int sensorValue4 = analogRead(sensor4);
+  // redefine range:
+  int paraC = map(sensorValue4, 0, 8191, 10, 1);
+
+
+  // sensor5: paraD
+  // read analog input
+  int sensorValue5 = analogRead(sensor5);
+  // redefine range:
+  int paraD = map(sensorValue5, 0, 8191, 50, 5);
+
+
+  // sensor6: paraE
+  // read analog input
+  int sensorValue6 = analogRead(sensor6);
+  // redefine range:
+  int paraE = map(sensorValue6, 0, 8191, 100, 10);
+
+
+  // sensor7: paraF
+  // read analog input
+  int sensorValue7 = analogRead(sensor7);
+  // redefine range:
+  int paraF = map(sensorValue7, 0, 8191, 10, 2);
+
+
+  // sensor8: paraG
+  // read analog input
+  int sensorValue8 = analogRead(sensor8);
+  // redefine range:
+  int paraG = map(sensorValue8, 0, 8191, 8, 2);
+
+
+  // sensor9: paraLine
+  // read analog input
+  int sensorValue9 = analogRead(sensor9);
+  // redefine range:
+  int paraLine = map(sensorValue9, 0, 8191, 10, 99);
+
+
+
+  
+  //put all the above values in a string to define the new data from this module:
+  newData = "&&&" + String(moduleID) + "," + String(font) + "," + String(paraA) + "," + String(paraB) + "," + String(paraC) + "," + String(paraD) + "," + String(paraE) + "," + String(paraF) + "," + String(paraG)  + "," + String(paraLine) + "&&&";
+
+
+ 
+ //Receive data from previous module (RX):
+  input = Serial1.readStringUntil('\n'); // read received data until line break and store in input variable
+
+  //LED
+  if (input != "") {
+    digitalWrite(sensorLED, HIGH); //turn LED on
+  }
+  else {
+    digitalWrite(sensorLED, LOW); //turn LED off
+  }
+
+
+  
+  output = input + newData;
+
+ //Send data to next module (TX):
+  Serial1.println(output); //the data received + new data 
+
+ //Print data on Serial Monitor:
+  Serial.println("This is the input I received: " + input);
+  Serial.println("Whoosh, new data: " + newData);
+  Serial.println("This is the output I send: " + output);
+
+
+  
+}